Go to the content
PROFECTRONICS
Test bench engineering · Nuclear measurement · Linz

Test benches and measurement systems from one house

From a single measuring point to a containerised plant. Mechanics, electronics, software and measurement from design through to acceptance — for thermal, fluid and power electronics testing and for nuclear measurement.

Focus areas in test bench construction

Visualisation · Test field with mobile test station, conditioning unit and autoclave test bench

Office, engineering and software in Linz. Assembly, piping, wiring and factory acceptance test in Neuhofen an der Krems.

Focus areas

4 focus areas in test bench construction

The focus areas are different in medium, size and measured quantity. In each focus area, Profectronics supplies mechanics, electrical engineering, software and measurement technology.

Focus areaTest specimen and test
Heat pumps and refri­gerationPerformance map over source and sink temperature, defrost and end-of-line test. Refrigerants also R290 and R744 (CO₂).
Chip emulator and cold plate test benchTest specimens: cold plate, manifold, quick-disconnect coupling and coolant distribution unit (CDU). The chip emulator simulates the heat flux density of the processor, with load steps.
Power elec­tronicsPower cycling to AQG 324, thermal resistance Rth(j-c) to JESD51-14 and double-pulse test.
Media condi­tioningTemperature, pressure, flow rate and humidity as the boundary condition for the test specimen. A record for each test run.

Environmental Solutions

Measuring instruments for radioactivity: aerosols and gaseous iodine in the air, stationary in the measurement cabin or mobile. Gamma spectrometry also as a drone payload and under water.

Measuring instruments of Environmental Solutions

The tables on the pages of the focus areas give the design values for pressure, flow rate and temperature.

All focus areas

Fluid engineering

3 tasks of a test bench

A test bench gives a test result if it does all 3 tasks.

Visualisation · Pressure pulse test bench with 6 test specimens

Condition the medium

The unit controls the temperature, pressure and flow rate of the medium and keeps them constant. Flow rate up to 180 m³/h, steady-state control deviation ± 0.1 K. The focus area Media conditioning gives the media.

Operate the test specimen

The unit supplies the test specimen with fluid and with electrical power. It controls the test specimen through CAN, CAN FD, LIN or Modbus. Residual bus simulation as necessary.

Do the test and record the evidence

Types of test: performance map, endurance test, leak test, end-of-line, position test and function test. The record contains the time stamp, the test equipment number and the calibration status.

Scope of services

Fluid engineering, electrical engineering and software

Profectronics makes the PLC, visualisation, control, measurement chain and test sequence. Profectronics does not buy the software and does not give it to a subcontractor.

01

Concept and functional specification

Profectronics makes a functional specification from the customer specification, traceable chapter by chapter. P&ID, 3D model, circuit diagram and parts list come from one source. Profectronics supplies the checked concept in approximately 2 weeks, before the order.

02

Engineering design

Thermal and hydraulic calculation, mechanics, electrical engineering with safety engineering and emergency stop concept, software and measurement technology. Tools: SolidWorks, EPLAN and Altium.

03

Assembly and factory acceptance test

Assembly, piping, wiring and factory acceptance test in Neuhofen an der Krems. Machining, sheet metal work, pipework and control cabinet construction with permanent partners.

04

Commissioning and maintenance

Calibration of the measurement chains, site acceptance test, CE documentation and training. On request, we offer maintenance and modification.

Profectronics makes the P&ID, 3D model and circuit diagram with its Concept Suite.

Service model

Engineering and assembly at Profectronics, parts manufacture with partners

Profectronics is responsible for design, project management and quality. Assembly, piping, wiring and factory acceptance test in Neuhofen an der Krems. Machining, sheet metal work, pipework and control cabinet construction with permanent partners.

At Profectronics

  • Design and engineering design
  • Software development
  • Project management
  • Assembly, piping, wiring and factory acceptance test
  • Commissioning and site acceptance test
  • Quality and conformity

With permanent partners

  • Machining and sheet metal work
  • Pipework
  • Control cabinet construction
  • Surface treatment
  • Transport and installation support

Profectronics works with a core team and permanent partners. History and team: About us.

Photo · Neuhofen an der Krems, assembly and factory acceptance test

One contract, one contact person, one warranty

The contract partner, the contact person and the warranty stay with Profectronics. Profectronics is responsible for the supply chain. For components with a long delivery time, we give the date in the quotation.

Service

Service in 4 levels

The levels are different in the level of commitment and in who pays for them.

LevelScopePaid by
WarrantyRepair of defects in the scope of supply of ProfectronicsProfectronics
MaintenancePeriodic inspection, calibration and maintenance to a planMaintenance contract
Fault repairWork outside the warranty, on a time and material basisCustomer
Modification and extensionNew order with its own acceptanceCustomer

The maintenance contract sets the response times for each service level. We agree them before we sign the contract.

Conformity

CE marking, Pressure Equipment Directive and ATEX

If Profectronics supplies the unit as a whole, Profectronics is the manufacturer.

As the manufacturer, Profectronics does the CE marking with risk assessment, technical documentation, operating instructions and declaration of conformity. If Profectronics supplies a part, Profectronics supplies the documents for the declaration of the manufacturer. The quotation gives the division of responsibility.

For units that are placed on the market or put into service from 2027-01-20, the Machinery Regulation (EU) 2023/1230 applies. Technical article: Test benches and the Machinery Regulation from 2027-01-20.

For R744, the Pressure Equipment Directive (PED) is part of the design. For R290, a zone concept with ventilation and gas detection and ATEX are part of the design. Characteristic values: Heat pumps and refrigeration.

Visualisation · Autoclave test bench, vessel moved out

Example of a special test bench: autoclave test bench with a pressure vessel of PED category IV. Characteristic values: Applications.

Limits

Scope of supply and limits

The table shows which services Profectronics supplies and which services it does not supply.

Service of ProfectronicsNot in the scope of supply
Test benches for thermal engineering, fluid engineering and power electronics from the design to the acceptance. Scope: conditioning, supply of the test specimen, control and measurement chainSensors for test benches as a separate product. Profectronics buys them and is responsible for their integration. Exception: the measuring instruments of Environmental Solutions.
Software of the test bench: PLC, visualisation, control, test sequence, record and calibration of the measurement chainTest bench software as a licensed standard product for units of other manufacturers
Modification, extension and maintenance of available test benches, also from other manufacturersTest runs and series of measurements for customers
CE marking as the manufacturer, with risk assessment and technical documentationTest laboratory and calibration services to ISO 17025. For these services, Profectronics works with accredited bodies.
Market position

Customers and market role

The customers of Profectronics are engineering service providers, manufacturers and operators of test fields.

Plant construction without test services

The customers do the tests. Profectronics supplies test benches and does not offer test services.

Enquiry

Data for an enquiry

An enquiry needs only 5 items of data: test specimen, medium, ranges for pressure, flow rate and temperature, installation site and date. A customer specification helps, but it is not a condition.

Send an enquiry